Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
The article author is making several good points about Tools You Need to Install a New Bathtub overall in this great article on the next paragraphs.
Setting up a tub isn't precisely rocket science, yet it does need solid plumbing, carpentry, and occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably tough project. If the old tub is conveniently available, the task can relocate rapidly; if you need to open up a wall to eliminate the old bathtub as well as place the new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will need an assistant to vacate the old tub and embeded in the brand-new one. Make certain you have actually certified on your own for the job and also fit attempting it. Rather than working with a service provider to take over a halfway-completed task, it is better to consider utilizing one before you start. Chances are you might need a professional plumber to make tube links.
This article will certainly help you set up a brand-new tub in your bathroom if you have already gotten a brand-new bathtub as well as don't need to alter the setup of your previous supply of water pipelines.
Your devices and material checklist ought to make up the following:
Getting ready for the Installment
First of all, the supporting framework provided with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of both taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of removing the existing faucets can be rather troublesome due to the limited gain access to that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Before going on to fit the new faucets, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the level checks out level.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water and also examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill up the bathtub and additionally check the overflow outlet and the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the bath tub should wait till the tub has been utilized at least once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washing machines remain in area in between the tap and the sink. Safeguard the faucet in place with the maker supplied backnut. As soon as the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type needs to be linked to the faucet ends initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, causing issues with moisture as well as feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can break rather early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly offered on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that entry about Installing A Bathtub while surfing the search engines. Sharing is caring. Helping others is fun. We recognize the value of reading our article about How to Install a Bathtub Yourself.
Issue? Dial fast! Report this page